Decorating · DIY · Quilting

Paper Pieced House Pillow

 

home_pillow_28JPGStill plugging away at small projects. This is 1 of 2 pillows made for the extra chairs at my old vintage table in the kitchen.  The little house is paper pieced and the flying geese are a fun little piecing technique, I’m sure many already know. I choose to do my pillow in Moda’s new line Well Said by Sandy Gervais, one bundle in my shop. This was great fabric for home decor projects.

I hope you enjoy!

Here’s the paper pieced pattern home paper piecing 003

Cut out your paper, leaving a space around the pattern, you will trim up later.

Out of white fabric, I cut 2 3/4 inch by WOF

Gingham chimney fabric 2 1/2″ x 6″

Roof fabric 3 1/2 x 9″

House fabric 6″ x 9″  plus (2) 2 1/4″ x 9″ pieces. pay attention if you use a directional fabric like I did!

Window fabric 2 1/2″x 10″

2″ for tiny separations in white

I’m not going to teach paper piecing, If you need to learn I strongly recommend a paper piecing class at your local quilt shop or Craftsy. I cut my fabric up in smaller pieces to work with so it’s easier and less waste.That’s why I gave the measurements, you don’t have to cut the fabric before if you don’t want to. Paper Piece the house how your used to doing it!

I paper pieced each section first, then started sewing sections together.Pay attention to the “Y” seams at the roof lines, chimney lines and house front and peak. Usually in paper piecing I sew off the edges, I actually stopped at these Y seam points and back stitched.

home_pillow_7home_pillow_8home_pillow_11home_pillow_12

All “Y” seams are started right at the point that they end, not at the beginning of a seam allowance. Go on You tube for how to do “Y” seams, I did a quick search and theres quite a few already there.

I know it’s hard to sew on the white sewing table but there is the paper piece house, I cut 1 1/2 ” border to put around the house, I did sides, trimmed and did top/bottom, trim and square.

To make the geese cut (2) 1 7/8″ x WOF  and many 3 1/4″ squares in your print fabrics.

Cut your white strip further into squares 17/8″ x 1 7/8″ , then mark the diagonal. Lay 2 white squares on the print squares, right sides together and sew 1/4 inch away from your marked diagonal line, both sides.home_pillow_16

home_pillow_17
lay your white marked squares on top of print large square, sew 1/4 each side and then rotary cut that entire pink line for 2 separate units

home_pillow_18

 

home_pillow_19
once your units are separated use 1 white square and line up at the only print corner, sew 1/4 inch each side, rotary cut the pink line and you will have 2 tiny flying geese!

Sew 2 sets of 5 flying geese and 2 sets of 6 flying geese, stacked on top of one another. Cut 2 1/2″ strips from your white, you will need 2 strips that are 2 1/2″ x 7 1/2″ strip and 2 that are 2 1/2″ x 10″, I trim and squares these measurements are a smidge big.

The shorter white goes to the stack of 5 geese, attach to top and bottom. Square and trim

The longer goes to the stack of 6 geese, attach to sides, square trim.

I added a decorative element of heat transfer vinyl in a matte navy in a swirly font. It’s featured on this pillow and a new matching pillow to this one. You can purchase both from my Etsy shop. Stay tuned for the matching pillow.

If you do a HTV decal attach it before quilting!

 

Make a quilt sandwich, I did some 1/4 quilting on the little house and tiny meandering on the rest.

I made my own binding and then finished the pillow with n envelope type back that I can just take out.

 

Stay tuned for the matching pillow and some other projects from this fat 8th bundle!

Thank you for stopping by, Colleen

One thought on “Paper Pieced House Pillow

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.